The Swivellink SLM-CB Table Clamp can be used to mount any Swivellink system on to the edge of a table between 16mm and 35mm thick. A screw with a plastic knob is used to tighten the SLM-CB. Machined from aluminium it includes a variety of drilled holes for fastening Swivellink SLM-1 or SLM-1XS bases to the Table Clamp Base.
CONTACT US regarding your requirement
IN STOCK
-
The Swivellink SLM-1 standard metric grey ball base has a slotted hole pattern to fit most metric T-slot aluminum extrusions or directly on to the mounting point of choice. The through hole in the ball base can be used for routing wires, cables, or small hoses. There is an exit groove out the side of the base for cables, hose, and wires. The Standard series can easily support 13Kg utilising the 30cm link (the longest in the series) in any position. CONTACT US regarding your requirement IN STOCK -
The Swivellink SLM-1XS Small metric grey ball base features two 5mm holes spaced at 25mm for attaching to your preferred base material. The through hole in the ball base can be used for routing wires, cables, or small hoses. There is an exit groove out the side of the base for cables, hose, and wires. The XS series can easily support 1.4Kg utilising the 10cm link (the longest in the series) in any position. CONTACT US regarding your requirement IN STOCK -
The Swivellink SLM-2 metric grey standard knuckle uses a double socket configuration to clamp to the ball of a standard base, standard link, or standard sensor mount. The design allows for a large range of motion while maintaining the internal hose and cable routing ability. The Standard series can easily support 13Kg utilising the 30cm link (the longest in the series) in any position. CONTACT US regarding your requirement IN STOCK -
The Swivellink SLM-2-2XS is a cross-over metric knuckle adapter designed to connect Standard to XS Series Fittings. It uses a double socket configuration to clamp to the ball of a Standard or XS base, link, or small sensor mount depending on the connection end utilised. The design allows for a large range of motion while maintaining the internal hose and cable routing ability. The Standard series can easily support 13Kg utilising the 30cm link (the longest in the series) in any position. CONTACT US regarding your requirement IN STOCK -
The Swivellink SLM-290 Standard series metric knuckle is designed as a tee connector working in conjunction with the Standard series SLM-3T Tee Link. It uses a double socket configuration to clamp to the ball of a small base, small link, or small sensor mount. The design allows for a large range of motion while maintaining the internal hose and cable routing ability. The Standard series can easily support 13Kg utilising the 30cm link (the longest in the series) in any position. CONTACT US regarding your requirement IN STOCK -
The Swivellink SLM-2XS small metric grey standard knuckle uses a double socket configuration to clamp to the ball of a small base, small link, or small sensor mount. The design allows for a large range of motion while maintaining the internal hose and cable routing ability. The XS series can easily support 1.4Kg utilising the 10cm link (the longest in the series) in any position. CONTACT US regarding your requirement IN STOCK -
The Swivellink Standard range utilises a series of link arms to extend the reach of the mounting system between knuckle couplers. The Swivellink SLM-3TSL-15-250 provides the flexibility to adjust or fit a precise link length of between 15 and 25cm long. It incorporates a through hole for routing wires, cables, or small hoses. For example this is ideal if you wanted to be able to adjust the height of a monitor. The design also allows for a large range of motion while maintaining the internal hose and cable routing ability. The Standard series can easily support 13Kg utilising the 30cm link (the longest in the series) in any position. CONTACT US regarding your requirement IN STOCK -
The Swivellink SLM-2XS90 small metric grey standard knuckle is designed as a tee connector working in conjunction with the XS series SLM-3XST Tee Link. It uses a double socket configuration to clamp to the ball of a small base, small link, or small sensor mount. The design allows for a large range of motion while maintaining the internal hose and cable routing ability. The XS series can easily support 1.4Kg utilising the 10cm link (the longest in the series) in any position. CONTACT US regarding your requirement IN STOCK -
Swivellink SLM-3T Standard Series Metric Tee Link The Swivellink Standard range utilises a series of link arms to extend the reach of the mounting system between knuckle couplers. The SLM-3T Tee link allows you to create two separate branches using a SLM-290 Tee Knuckle connector attached to the centre ball. It incorporates a 19mm diameter through hole for routing wires, cables, or small hoses. The centre ball is machined with a 19mm x 38mm slot for the same purpose. The design allows for a large range of motion while maintaining the internal hose and cable routing ability. The Standard series can easily support 13Kg utilising the 30cm link (the longest in the series) in any position. CONTACT US regarding your requirement IN STOCK -
The Swivellink Standard range utilises a series of LINKS to extend the reach of the mounting system between knuckle couplers. Where a Link piece is not long enough for needs adapting the SLM-3 Ball Adapter can be used instead. It is a standard 28.5mm ball with a 3/8"-19 BSPT thread so you can attach a pipe of any length! The ball includes machined spanner flats for tightening the pipe on the the adapter. The design allows for a large range of motion while maintaining the internal hose and cable routing ability. The Standard series can easily support 13Kg utilising the 30cm link (the longest in the series) in any position. CONTACT US regarding your requirement -
The Swivellink SLM-4 Button Mount enables you to fit a push button into your system. For example a machine might require the provision of a cycle start or emergency stop button. The SLM-4 is threaded M30 x 1.5 and has plenty of room for the cable connection inside. The robust design allows for a large range of motion while maintaining the cable routing ability. The Standard series can easily support 13Kg utilising the 30cm link (the longest in the series) in any position. CONTACT US regarding your requirement -
The metric grey SLM-6 blank mounting plate is designed so you can drill and mount your equipment on to a plate. The SLM-6 includes drillings to accommodate the SLM-1 Standard Ball Base plus a slot to accommodate the exit of cables, wire or pipes that have passed through the centre of the Swivellink system. Four M5 x 14 socket cap setscrews are included for attaching the SLM-1. The Standard series can easily support 13Kg utilising the 30cm link (the longest in the series) in any position. CONTACT US regarding your requirement IN STOCK -
The Swivellink SLM-570XS-GP Small XS Series Metric GoPro Mount allows you to attach any device with a standard blade type GoPro mount. This makes Swivellink an ideal high quality mounting system for action cameras of all kind. As well as standard GoPro cameras and housings this mount enables you to directly attach the BackBone H8PRO modified Hero8 Black camera. The XS series can easily support 1.4Kg utilising the 10cm link (the longest in the series) in any position. CONTACT US regarding your requirement IN STOCK -
The Swivellink SLM-6XS Small Metric XS Series Blank Mounting Plate is designed so you can drill and mount your equipment on to a plate. The SLM-6XS includes drillings to accommodate the SLM-1XS Small Ball Base in a choice of two positions. Two M5 x 12 socket cap setscrews are included for attaching the SLM-1XS. The XS series can easily support 1.4Kg utilising the 10cm link (the longest in the series) in any position. CONTACT US regarding your requirement IN STOCK -
The Swivellink SLM-5XS Small Ball 1/4"-20 (1/4"UNC) Male Tripod Mount is designed to attach to cameras, mounting plates, etc with a standard tripod mount. The 18.5mm ball can attach to Swivellink XS knuckles and tightened on to cameras, etc by a 11mm wide flat. For heavier cameras the SLM-5XS can fit Standard Swivellink components by attaching to the SLM-2-2XS coupler adapter. SeeSense also offer a SPECIAL version of this part with a 1/4-20 (1/4"UNC) female thread - SLM-5XSF.The XS series can easily support 1.4Kg utilising the 10cm link (the longest in the series) in any position. CONTACT US regarding your requirement IN STOCK